Cb0178-12 load data.

I've been loading a 7/8 oz skeet load with 17.7 gr of Competition, CB4100-12b or CB0178-12 wads and Cheddite primers. I've been happy with the performance. Velocity around 1250 and 7,500 psi for the CB0178-12 wad. No published data for a 7/8 oz load with the Windjammer clone wad (4100-12b) but if anything the pressure would be lower.For 7/8 ounce loads I'm pretty much dead set on Claybuster CB0178-12 or WAA12L clones (grey ones), as there are several published loads for those. ... 7/8's Ounce Shot Loads Winchester Hull Primer Powder Grains Velocity F.P.S. Pressure P.S.I WIN 209 Clays 17 1200 7000 WIN 209 Clays 18 1250 7500Exactly the same. The overall height is about 1/16" shorter than the CB0178-12, but that doesn't matter. The XXL Pink's petals stand straight, whereas those of the CB0178-12 are flared out a bit, still no big deal. Flip a coin or go for the cheapest - either is an excellent wad, especially for 3/4 and 11/16 oz. payloads.Take a look at International Clays. Really, 12 and 20 would do best with two different powders, especially if you want to load 1 oz. in the 12ga. The 20ga calls for a slower powder which is really only truly suitable for heavier 1-1/8 or 1-1/4 oz 12ga loads. International, even, is a bit too fast for 20 ga and your pressures get pretty high.

As per Hodgdons reloader website, 17.5 gr Ramshot competition, WAA12L wad - claybuster CB0178-12 equivalent, HS hull, cheddite primer, 1250 FPS. Wonderful load, low recoil, hits hard to smoke birds. Another tip, I've just started to use Winchester red Super Target hulls, they load great and they are all over the place, use them once or twice ...

These loads were developed for use in Cowboy Action shooting, and were designed to duplicate the performance of the Winchester Low Recoil/Low noise loads, which are 26 Dr. loads. ... Clear Duster wad, or Claybuster CB0178-12 7/8 oz. shot of your choosing, I use 7-1/2's. For loads using WAALITE powder, Winchester lists this: Winchester Cases, W ...

Alliant recommended Extra Lite with a CB0178-12, but Extra Lite isnt available locally. Suggestions or experience with these loads? ... I did also try the minimum load data which is 13.2 grains and runs at 1,150 fps @ 7600 PSI. Very light and will still break clays at 16 yards; but crimps start to dish inward.For the tapered, compression-formed Remingtons and (sort of tapered) AAHS hulls, use the Down Range XXL Pink or Claybuster CB0178-12. Actually, you can use those wads suited for the Federal hulls in the Remingtons and Winchesters, but stay well short of maximum-pressure loads, since those wads will fit very tightly and can raise pressure.For 12 ga, I load Remington STS hulls with 7/8 oz of #7.5, 17 grains of E3 and more or less any 209 primers (I use CCI) with Claybuster CB0178-12 wads, consistent loads that bust clays all day long. Nice light load, low recoil in my Beretta 391.CB0175-12 Reloading Data ~ ¾ Ounce Shot Loads. J-Ron Inc.'s Claybuster Wad Line is a well established economical wad line built for target-shooters and wing-shooters alike. With twenty-one different models from which to choose, the Claybuster Wad Line can satisfy nearly every target or wing shooting application for reloading.OK, the load data that Hodgdon gave you should have specified a wad. If they were talking Winchester, the WAA12L is gray and, and CB equivalent is the gray wad CB0178-12 If they suggested the WAAA12SL, which is pink, the CB equivalent is CB1100-12. Also pink. Normally, those 2 gray wads work best with 7/8 ounce shot.

Perfect Pattern has some of the lowest recommended grain drops I've ever seen listed for 12 gauge 1oz loads using WAA12L wads. 1 lists 12.1 and another 12.9 grains with a Cheddite primer. Heaven Has Strict Immigration Laws. ... cheddite, 16.3 grains titewad, cb0178-12, and 7/8 oz shot. Cycled my 1100 with ease and broke targets as well as any ...

The CB0178-12 wad was designed for use in 7/8 oz to 1 oz trap, skeet, or sporting clays loads. Technical Information: •Replaces the Winchester WAA12L •Optimal Load: 7/8 oz •Intended as an economical wad replacement for target and wing shooters •Wads are made with 100% prime resin for consistency These are the best wads to use for ...

Sheet1 Page 1. CB0175-12 Reloading Data ~ ¾ Ounce Shot Loads. Powder Grains Primer Velocity Pressure. ¾ Extra-Lite 14.5 Win 209 1225 6900 ¾ Extra-Lite 15 Win 209 1260 7300 ¾ Extra-Lite 16 Win 209 1300 7600 ¾ Red Dot 15.2 Win 209 1200 5900 ¾ Red Dot 16 Win 209 1250 6300 ¾ Red Dot 16.5 Win 209 1300 6700 ¾ Clay Dot 15.5 Win 209 1200 5800 ...CB4100-12 Reloading Data ~ 1 Ounce Shot Loads. J-Ron Inc.'s Claybuster Wad Line is a well established economical wad line built for target-shooters and wing-shooters alike. With twenty-one different models from which to choose, the Claybuster Wad Line can satisfy nearly every target or wing shooting application for reloading.CB0178-12 (WAA12L). For use in 7/8 to 1 oz. trap, skeet or sporting clay loads. Performs best in tapered hulls, Remington or Winchester. Specifications and Features: REPLACES WINCHESTER WAA12L. Check your reloading manual or go to a powder manufactures website for load data. WARNING: This product contains chemicals known to the State of ...17.5gr of Red Dot, 7/8 oz of #8 shot, CB0178-12 gray wads, and Rem 209 primers in Gun Club hulls. ... 7800 PSI (estimated from CB load data) This recipe is from the CB lightning load card that comes with the wads. I patterned this load and chronographed it just a few weeks ago with excellent resultsLoad Data. CB0178-12 (WAA12L) For use in 7/8 to 1 oz. trap, skeet or sporting clay loads. Performs best in tapered hulls, Remington or Winchester. Optimum load is 7/8 oz. Featuring Lead-in Taper. Product Testimonials. CB1100-12 (WAA12SL) For use in 7/8 to 1 oz. trap, skeet or sporting clay loads.STS Hull--F209-A primer--17.5 Green Dot--CB0178 grey wad--and 7/8 of of your choice. This load is a great skeet load when loaded with 9s amd a great 16 yd trap load when loaded with 8s. ... you mean our version of the TGT-12". That really set me back a bit, because I see no similarity and the TGT-12 is marginal, at best, for any 7/8 loads. Save ...

I've used the Claybuster CB1118-12 (WAA12 type) for some of my 1-1/8 oz loads, they seem to work OK at just a little over 1200 FPS but hadn't tried the CB0178's. I haven't had too much trouble with the crimps, but I'm only on my 2nd or 3rd time around on most of these hulls. With twenty-three different models from which to choose, the Claybuster Wad Line can satisfy nearly every target or wing shooting application for reloading. The wads are manufactured, and have always been manufactured, with 100% prime resin so a consistent quality product can be expected with every purchase. Nostrjr. 255 posts · Joined 2018. #7 · Jul 17, 2022. I'm not sure about published data but I use Remington hulls, claybuster gray 7/8 oz wads cheddite primers and 15 grains of claydot. Pretty nice load. This is an older thread, you may not receive a response, and could be reviving an old thread. Please consider creating a new thread.Many wads for target load applications are available at Ballistic Products. Corcoran, Minnesota | 763.494.9237 ... See our Advantages Manual or High Performance for Clays for reloading data. CS12S Comp Special Short 12ga (250/bag) Item #: 072CS12S In Stock ... Claybuster CB0178-12 WAA12L (500/bag) Item #: 030CB12L In Stock $14.49. X12X ...It is also reported that REX-0 is a great powder for these reduced loads. Yes, I know you have this International powder and want to use it. Fine, do so, but in loads it is compatable with. Light 3/4 and 7/8 oz. loads are not where it shines. Personally I load 7/8 oz loads with 17.3 Promo, a CB0178-12 wad, and any medium strength primer.For 7/8 oz. loads in the Rems and AA CF cases, the Clear Duster or the CB0178-12, will give the best fit in these cases. This leaves you with only 3 wads, needed for all AA or Rem cases, and will allow for loading either 1 oz. or 7/8 oz. loads. 1) DRA-12 Pink 2) Either the DR XL-1, or the Green Duster 3) Either the Clear Duster or the CB0178-12

CB3118-12A Reloading Data ~ 1 1/8 Ounce Shot Loads. J-Ron Inc.'s Claybuster Wad Line is a well established economical wad line built for target-shooters and wing-shooters alike. With twenty-one different models from which to choose, the Claybuster Wad Line can satisfy nearly every target or wing shooting application for reloading.

I shoot 7/8 oz 12 ga loads for skeet (1250 fps reloads with #9 or 8.5 shot) and 1 oz for trap (1275 fps reloads with #8 or 7.5 shot). ... CB0178 -12 and Nobel Sport primers in AA and GC hulls of #9s for skeet. This is a ~ 1200 fps load. Radicalized by the US Constitution. Reactions: Unclefish. Save Share. Like. DooFighter.Gauge. 12 Gauge. Model. CB0175-12. Quantity. 500. Claybuster 12 Gauge 3/4 oz Wads - Claybuster wads are intended as an economical wad replacement for name brand wads. The Claybuster wads are ideal for target and upland game shooters. These wads are constructed from 100% prime resin for consistency from shot to shot.The Hodgdon load data for Clays calls for 16.9 grains and and a WAA12SL 1 oz. wad. My specific question is there any problem substituting the wad for the Claybuster CB178-12 which is a clone of the WAA12L 7/8 oz. wad. ... Incidentally the bushing is what I use for my E3 load, which is 15.5 grains, CB1100-12 (pink), Cheddite primer, 1183 fps ...Zero wad pressure. 2. Lower the precrimp as far as possible, just before it buckles the case. 3. Adjust the cam for maximum "swirl" in the crimps. Follow the manual instructions for removing a hole in the crimp. 4. Raise the crimp depth until it just barely flattens the crimp.D L Marcum. What we are not seeming to get across, is the fact that in the 12 ga., the lighter the payload, the faster burning the powder must be to get good efficiency. It's just silly to even try to use Red Dot in 1-1/4 oz loads. By the same token its just as silly to use Green Dot or Unique in 3/4 or 7/8 oz. loads.Comparable to what's already posted I'm about halfway through my first 8 lbs jug of Clay Dot alternating between 1 oz and 7/8 oz loads using Remington hulls, Nobel primers, and Claybuster wads (specifically CB1100-12, CB0178 and CB4100). I'm averaging drops of 18.2 grains using a MEC 32 bushing.The bag states that they are a replacement for the CB0178 & WAA12L wads. They aren't. These wads are more of a replacement for CB1100, WAA12SL and CB8100 wads regarding stack height. I recently loaded up some 7/8 oz skeet loads with them and was disappointed that they were not a replacement for the CB0178 wads I had been using.Hornady Manufacturing Company develops and publishes reloading data for the Handbook of Cartridge Reloading. Occasionally, we will temporarily publish load data on this page when a bullet becomes available and is not yet listed in the latest edition of the handbook. 6.5mm .264" 100 gr. ELD-VT™ [PDF] 22 ARC (Bolt Gun) [PDF] 22 ARC (Gas Gun) [PDF]View Reviews | Review this item. $14.49. In Stock. Quantity. Detailed Description. Claybuster CB4100-12B Lightning (Windjammer-Style) wads (500/bag) The Claybuster wad line is an economical wad line built for target-shooters and wing-shooters alike. With twenty-five different models from which to choose, the Claybuster wad line can satisfy ...As TT says, use the CB0178-12 clone of the gray WAA12L and you shouldn't have any problems with dished crimps on a 1 oz. or 7/8 oz. load. That's one of, if not the tallest 12 gauge wad made and is perfect for 24 gram and 7/8 oz. loads. If it's a little too tight with 1 oz., use the CB2100-12 clone of the Federal 12SO or the CB110-12 clone of ...

Many investors turn to mutual funds because the funds can make it fairly easy to see solid returns while maintaining a degree of diversity. Many investors turn to mutual funds beca...

There's a loading data sheet included in the bag of Claybuster 6100 wads. BUT, no loads lighter than 1 ounce of shot. ... The CB6100 (neon green) or the CB0178 (gray) wad will be taller. The 6100 is the one made for 1 ounce of shot. ... 7/8 ounce of shot in the CB0178-12 wad. Which doesn't do a good job of sealing the hull giving poor …

WAA12L or CB0178-12 wad W209 or Remington primer Oehler Model 35 chronograph results: Average velocity: 1210 ... The limited 20 ga 3/4 oz load data, on the other hand ...They are the best wads I have ever used in my 50 years of reloading." Testimonials - CB4100-12 ... I've also been very happy with the CB0178 wads too. Remington STS hull or GC Rem STS209 primer 17.5 grains Titewad 7/8 ounce of shot CB4100 wad Very close to 1250fps according to Hodgdon site ... I have been using your CB4100-12 (Lighting) 12 ga ...International Clays/Winchester 209/CB0178-12 7/8 oz. load data. Title says it all. I've been using this load for several years at 20.2 +-grains of International Clays, but …I am using the following loads. These sound like the loads you are looking at. Winchester AA Winchester 209 18.5 Grs 700-X Claybuster CB0178-12 (AA12L) 7/8 #9 Magnum Lead shot FPS 1,325 Winchester AA Winchester 209 18.0 Grs 700-X Claybuster CB1100-12 (AA12SL) 1 oz. #9 Magnum Lead shot FPS 1,250 I use the 7/8 oz. for skeet and the 1 oz. for ...With our load data you can search by caliber, bullet weight, powder, powder manufacturer or a combination of all four. Search over 311,644 loads! Metallic Search ... John Haviland / Wolfe Publishing 12/5/2019 . In this age of ever-increasing propellant specialization, it’s nice to have a powder that works in a broad range of rifle and handgun ...Claybuster Shotshell Wads - 12 GA 7/8 OZ GrayHODGDON ATTENDS 2022 NRA SHOW. PR Contact: Aaron Oelger [email protected] 6430 Vista Drive Shawnee, KS 66218 Phone: (913) 745-0776 Fax: (913) 362-1307 Press Release May 26, 2022 Hodgdon Powder Company, Inc. to Attend the.I did find RamShot Competition, and use their 7/8-oz load data to load 3/4-oz loads. Load: Rem-STS 12 / Win209 / 21.0-gr Comp / CB-0175 / 3/4-oz hard #8-1/2. Competition is a spherical powder, meters very well in my equipment, and the load data will support heavier shot loads by using a different wad. No dished crimps, easy to transition from 3 ...Win 209 primer. Claybuster CB5050-410HS wads. 296 or H110 powder (they are the same ST marks powder, so pick up which every branding name is cheaper) and this powder will give the hulls the longest reloading life. Ream the shot bushing to throw 226Gr of shot in your reloading. The stock 1/2oz bushing is going to throw about 214grs, true 1/2oz ...I'm loading 7/8 oz shot in Federal and estate hulls for practice and I'm getting dished in crimps in the Fed hulls. My stack height appears to be too low. Here is the recipe I'm using which is for 24gm loads. 24 gm 700-X Win. 209 CB 2100-12 18 6,500 PSI 1250 24 gm 700-X Win. 209 CB...

Detailed Description. Claybuster CB1078-12 WAA20 wads (500/bag) The Claybuster wad line is an economical wad line built for target-shooters and wing-shooters alike. With twenty-five different models from which to choose, the Claybuster wad line can satisfy nearly every target or wing shooting application for reloading.Tim from Manhattan, KS. I'm currently using your CB1100-12 with great success. I'm on my 5th case and will only use Claybuster products. To receive additional information: J-Ron, Inc. [email protected]. Customer Service: 800-922-6287. 635 Bob Posey Street. Henderson, KY 42420.The Lee Loadall isn't nearly as bad as I thought it was going to be. It really works well for $60. I'm loading 14gn of Clays, 7/8oz of number 8 with a Claybuster CB0178-12 wad in Winchester AA hulls for Cowboy Action Shooting.Jul 2, 2014 · CB0178-12, DR XXL Pink, MEC78T4 You could argue about whether they are really the same or not, but at a minimum, they are at least similar. At the kind of pressures they list for the 700X-7/8 ounce loads, similar is plenty good. In fact, a CB0178-12 is real, real similar to an AA12L. Instagram:https://instagram. lmu dcom residency placementnaca section 8 applicationhayes market waymartrebecca black net worth 2022 I've used the Claybuster CB1118-12 (WAA12 type) for some of my 1-1/8 oz loads, they seem to work OK at just a little over 1200 FPS but hadn't tried the CB0178's. I haven't had too much trouble with the crimps, but I'm only on my 2nd or 3rd time around on most of these hulls. arrionne curryffxiv gc ranks Load Titles: Number of Loads: 12 Gauge (Alliant Data): 2 3/4 Fed. Paper Target Shells: 175: 12 Gauge (Alliant Data): 2 3/4" Cheddite Plastic Shells: 22: 12 Gauge (Alliant Data): 2 3/4" Federal 7/16 Paper BW - Steel Shot: 1: 12 Gauge (Alliant Data): 2 3/4" Federal Gold Medal (Steel Shot Only) 7: 12 Gauge (Alliant Data): 2 3/4" Federal Gold Medal ... how to upgrade electric fighting style blox fruits So the whole load data is the Remington 12 gauge STS or Gun Club hulls, Winchester 209 primers, 24 Grains of Hi-Skor 800x powder, ClayBuster CB0178-12 wads which are replacements for the WAA12L, 1/8" thick Nitro Card (x2) in the wad cup, then the 7/8oz Lee Key Drive slug on top of the nitro cards, finished off with a factory 8-point crimp.The breaks looked a lot better than the cb0178-12 and my barrels looked a lot better too (less wad fouling). ... Here is a link to Claybusters load data for their 3/4 oz 12 ga wad. I shoot 80% of my skeet practice with the 3/4 oz 12 ga, and tight chokes!! CB0175-12 Load Data